search

Skyrc RS16 180W/16A Balance Charger/Discharger User Manual Page 12

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 11
Number
of
cells
Elapsed
time
Charge
or discharge
current
Supplied
capacity
Current
voltage
battery
This screen shows the real-time status
charging. Move the joystick left to stop the
charge process.
joystick left to go back to previous screen to
recheck the number of cells of the battery
pack before going ahead.
DISCHARGING LITHIUM BATTERY
Number
of
cells
elapsed
time
Battery
voltage
Discharged
capacity
discharge
current
The value of discharge current on the left
can not exceed 1C, and the value on the
right can not be under the voltage
recommended by the manufacturer to avoid
over discharging. move the joystick right and
hold it for 3 seconds to start discharging.
This screen shows the real-time status of
discharging, you can move the joystick left
to stop discharging.
This screen displays the number of cells you
set up and the processor detects. R shows
the number of cells detected by the charger
and S is the number of cells set by you at
the previous screen. If both numbers are
identical you can move the joystick right to
start charging process. If not, move the
joystick left to go back to previous screen to
recheck the number of cells of the battery
pack before going ahead.
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
RIGHT
RIGHT
> 3 seconds
UP DOWN
-
+
UP DOWN
-
+
LEFT RIGHT
NIMH/NICAD BATTERY PROGRAM
These programs are for charging or discharging NiMH (Nickel-Metal-
Hydride) or NiCad (Nickel-Cadmium) battery.
CHARGING OF / BATTERYNIMHNICAD
The charger will charge NiMH and NiCad batteries using the charge
current set by the user.
NiMH CHARGE
CURRENT 2.0A
Battery
type
Elapsed
time
Charged
capacity
Battery
type
Charge
current
Battery
voltage
The screen displays the current state of
charging.
To stop the process, move the joystick left.
The audible sound indicates the end of
process.
This program is for charging of NiMH/NiCad
batteries. You can move the joystick right to
make the parameter blink, then move the
joystick up/down to change the value and re-
move the joystick right to store the value.
CHARGING / BATTERY IN THE AUTO
CHARGE MODE
NIMHNICAD
In this program the charger detects the condition of the battery which is
connected to the output and automatically charges the battery. In this
mode, you should set up the upper limit of the charge current to avoid
damage by excessive feeding current. Some batteries of low
resistance and capacity can lead to higher current in the auto charging
mode.
NiMH Auto CHARGE
CURRENT 2.0A
This program is for charging of NiMH/NiCad
batteries in auto mode. You can move the
joystick right to make the parameter blink, then
move the joystick up/down to change the value
and re-move the joystick right to store the value.
Battery
type
> 3 seconds
UP DOWN
-
+
LEFT RIGHT
> 3 seconds
LEFT RIGHT
Page view 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments
Related products and manuals for Power suppliers Skyrc RS16 180W/16A Balance Charger/Discharger
Power suppliers Skyrc T6200 Charger User Manual   (14 pages)
Power suppliers Skyrc iMAX B6 Mini Charger User Manual   (28 pages)
Power suppliers Skyrc eFuel 230W/17A Power Supply User Manual   (6 pages)
Power suppliers Skyrc eFuel 1200W Power Supply User Manual   (2 pages)
Power suppliers Skyrc eFuel 30A Power Supply User Manual   (2 pages)
  • PSSO Microwave networks Mobridge Luminox BrightSign
  • Lincoln Ovens Artwizz Mobile phone cases Sony Cable splitters or combiners Zanussi Unknown Haier Dishwashers
  • Sony SA-VA10 LG 75UM3C-B Yamaha SLG130NW Sony XBA-3iP
  • Uniden DSC User Manual Acer X183H User Manual LG 24BK750Y-B User Manual Conceptronic CM3PVR User Manual Brother MFC-885CW User Manual